Table of Contents

How to Convert Standalone Apache to LiteSpeed

This wiki covers how to set up LSWS on a server that already has a working Apache installation but no control panel.

Step 1: Install LiteSpeed Speed Web Server

1.1 Download

Download LSWS tarball from the LiteSpeed Technologies website.

Run the following commands from SSH as root

cd /root
wget http://www.litespeedtech.com/packages/5.0/lsws-5.3.8-ent-x86_64-linux.tar.gz

Note: Replace the values in the URL to control for your OS and which version/edition of LSWS you wish to download:

lsws-5.3.8-ent-x86_64-linux = LSWS Enterprise 5.3.8 for 64bit Linux

lsws-5.3.8-std-i386-linux = LSWS Standard 5.3.8 for 32bit Linux

lsws-5.3.8-ent-x86_64-freebsd6 = LSWS Enterprise 5.3.8 for 64bit FreeBSD 6.x

1.2 Unpack

tar zxfv  lsws-5.3.8-ent-x86_64-linux.tar.gz

1.3 Run the installation script

For Enterprise Edition, make sure to put the license file (trial.key or paid license serial.no file) in the unpacked folder.

cd lsws-5.3.8
./install.sh

The installer will ask you a number of questions (covered in detail here). Choose the default setting when in doubt, but you have to set the same username and groupname as Apache for LiteSpeed process to run as (choosing LiteSpeed default setting nobody:nobody may create file permission problem):

Step 2: Install PHP

Enable the LiteSpeed repository and download LSPHP from our repository. See instructions here.You may have default php.ini file installed through RPMs and You just need to make some changes to match it to exiting Apache PHP. Check both phpinfo pages for difference.

Step 3: Load Apache Configuration in LSWS

Open the LiteSpeed WebAdmin Console and, under Configuration > Server > General, change configurations in Using Apache Configuration File table.

Load Apache Configuration => Yes
Auto Reload On Changes => Use Apache Binary Wrapper 
Apache Configuration File => /usr/local/apache/conf/httpd.conf
Apache Port Offset => 2000 (Try LiteSpeed on port 2080 and 2443 first, change to 0 later, do NOT use 8088 or 8008)
Apache IP Offset => 0 
PHP suEXEC => Yes (Run PHP in suEXEC mode)
PHP suEXEC Max Conn => 5 (The maximum PHP processor each account can have)

Note:

Sometimes your Apache conf file may have environment parameters set in /etc/apache2/envvars or other locations, such as:

User ${APACHE_RUN_USER}
Group ${APACHE_RUN_GROUP}
...

You have to include it in “Apache Environment” within “Using Apache Configuration File” table in the Web Admin Console.For example:

APACHE_RUN_USER=www-data
APACHE_RUN_GROUP=www-data
APACHE_PID_FILE=/var/run/apache2.pid
APACHE_RUN_DIR=/var/run/apache2

If LiteSpeed runs into some absolute path problem such as

[/etc/apache2/apache2.conf:250] Failed to get absolute path for [/usr/local/apache/ports.conf]!
2015-07-06 12:37:03.282 ERROR [/etc/apache2/apache2.conf:267] Failed to get absolute path for     [/usr/local/apache/conf.d/]!
2015-07-06 12:37:03.282 ERROR [/etc/apache2/apache2.conf:270] Failed to get absolute path for   [/usr/local/apache/sites-enabled/]!
2015-07-06 12:37:03.582 ERROR HttpListener::start(): Can't listen at address 127.0.0.1:80: Address already in use!
2015-07-06 12:37:03.582 ERROR HttpServer::addListener(127.0.0.1:80) failed to create new listener
2015-07-06 12:37:03.882 ERROR HttpListener::start(): Can't listen at address 63.247.170.35:80: Address already in use!
2015-07-06 12:37:03.883 ERROR HttpServer::addListener(63.247.170.35:80) failed to create new listener
2015-07-06 12:37:03.883 ERROR [:5] Listener for default is not available!
2015-07-06 12:37:16.601 ERROR [ADMIN] authentication failed!
2015-07-06 12:38:12.156 ERROR [ADMIN] authentication failed!

which simply means your apache2 configuration may have some relative path problem. You may just set server root in apache2 configuration to clear all above absolute path errors.

ServerRoot "/etc/apache2"

Most of the time, LSWS loads your Apache configuration straight away without any error.

Step 4: Test and switch to LiteSpeed

If your application doesn't allow you to run offset port for LSWS, such as WordPress, Magento,etc, you should stop Apache webserver and start LSWS for testing.

If your application allowed, you can set port offset such as 2000 then start LSWS and try websites hosted on offset port 2080 and secured sites on port 2443. This way you may run both Apache (port 80 or 443) and LiteSpeed (port 2080 or 2443) at the same time. Most of the time your website is running smoothly and very faster already.

If there is any problem, probably a PHP issue, you need to check LSWS error log, LSWS stderr log or PHP errors log for details. Server error log and stderr log are set to the following location by default unless you customize it.

/usr/local/lsws/logs/error.log
/usr/local/lsws/logs/stderr.log

For PHP error logs, they are normally located in the directory where PHP script runs:

You may go to your server document root and find them:

find . -name php_errors.log

You should check the php_errors.log for the corresponding location where the PHP script running into problems. Try to clear the errors, which may fix the problem. Sometimes even undefined date.timezone in php.ini may cause problems.

If all sites work properly, stop Apache, change “Apache Port Offset” to 0, restart LSWS, all hosted web sites are powered by LiteSpeed now.

Note: Remember to change rc script configuration to remove httpd from the services that get started automatically during a reboot. For example, On CentOS, try this from a root shell:

 chkconfig httpd off

You may also want to add lsws to be started automatically during a reboot:

 chkconfig lsws on

On Debian, try the following:

update-rc.d -f apache2  remove
update-rc.d lsws defaults

Step 5: Monitor

If you have a script that monitors for the web server process, remember to update it to reflect the location of LSWS.

That's it.