Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
litespeed_wiki:lsmcd:interaction [2016/04/06 19:11] Rob Holda [bget] |
litespeed_wiki:lsmcd:interaction [2016/04/06 20:00] Rob Holda removed |
||
|---|---|---|---|
| Line 1: | Line 1: | ||
| - | ====== Interacting with LSMCD ====== | + | ====== LSMCD Commands ====== |
| In order to connect to and interact with LSMCD, you can use telnet to connect to a one of the IP addresses and port numbers set in **Cached.Addr**. For example, with the default settings, you would connect using the following command: | In order to connect to and interact with LSMCD, you can use telnet to connect to a one of the IP addresses and port numbers set in **Cached.Addr**. For example, with the default settings, you would connect using the following command: | ||
| Line 6: | Line 6: | ||
| </code> | </code> | ||
| - | ====== LSMCD Commands ====== | + | The following is a list of LSMCD commands useable in telnet, each with a description, the command's syntax, an example of use (including user input and system output separated by an empty line), and an explanation of potentially confusing values. Note: in the syntax sections, values enclosed in <> indicate a required value while values enclosed in [] indicate an optional one. |
| - | + | ||
| - | The following is a list of LSMCD commands useable in telnet, each with a description, an example use (including user input and system output), syntax, and an explanation of potentially confusing values. Note: for syntax, < and > indicate a required value while [ and ] indicate an optional one. | + | |
| ===== get ===== | ===== get ===== | ||
| Line 32: | Line 30: | ||
| ===== bget ===== | ===== bget ===== | ||
| - | Binary get. | + | Read a binary value. |
| **syntax:** | **syntax:** | ||
| Line 43: | Line 41: | ||
| VALUE mykey 0 10 | VALUE mykey 0 10 | ||
| - | 1011101010 | + | abcdefghij |
| END</code> | END</code> | ||
| **output notes:** | **output notes:** | ||
| Line 51: | Line 49: | ||
| ===== gets ===== | ===== gets ===== | ||
| - | Read a value and its **cas token** (to be used with the **cas** command). | + | Read a value and its cas token (to be used with the **cas** command). |
| **syntax:** | **syntax:** | ||
| Line 60: | Line 58: | ||
| <code> | <code> | ||
| gets mykey | gets mykey | ||
| - | </code> | + | |
| - | **output:** | + | |
| - | <code> | + | |
| VALUE mykey 0 10 9 | VALUE mykey 0 10 9 | ||
| - | myvalueabc | + | myvalueabc |
| - | END | + | END |
| </code> | </code> | ||
| **output notes:** | **output notes:** | ||
| * **0** → no flags | * **0** → no flags | ||
| * **10** → Size in bytes | * **10** → Size in bytes | ||
| - | * **9** → unique **cas token** number | + | * **9** → unique cas token number |
| ===== add ===== | ===== add ===== | ||
| Line 82: | Line 78: | ||
| <code> | <code> | ||
| add newkey 0 120 10 | add newkey 0 120 10 | ||
| - | </code> | ||
| - | **output:** | ||
| - | <code> | ||
| myvalueabc | myvalueabc | ||
| - | STORED | + | |
| + | STORED | ||
| </code> | </code> | ||
| **output notes:** | **output notes:** | ||
| Line 101: | Line 95: | ||
| set <key> <flags> <TTL> <length> [noreply] \r\n <value> \r\n | set <key> <flags> <TTL> <length> [noreply] \r\n <value> \r\n | ||
| </code> | </code> | ||
| + | |||
| + | **parameters:** | ||
| + | * **flags** - A 32-bit unsigned integer that the server stores with the data provided by the user, and returns along with the data when the item is retrieved. | ||
| + | * **TTL** | ||
| + | * **length** | ||
| + | * **noreply** | ||
| + | * **value** | ||
| + | |||
| **example:** | **example:** | ||
| <code> | <code> | ||
| set mykey 0 120 10 | set mykey 0 120 10 | ||
| - | </code> | ||
| - | **output:** | ||
| - | <code> | ||
| myvalueabc | myvalueabc | ||
| - | STORED | + | |
| + | STORED | ||
| </code> | </code> | ||
| - | **output notes:** | ||
| - | * **0** → no flags | ||
| - | * **120** → TTL in seconds | ||
| - | * **10** → Size in bytes | ||
| - | * **myvalueabc** → value to set "mykey" to | ||
| - | |||
| ===== replace ===== | ===== replace ===== | ||
| Line 127: | Line 121: | ||
| <code> | <code> | ||
| replace mykey 0 120 10 | replace mykey 0 120 10 | ||
| - | </code> | ||
| - | **output:** | ||
| - | <code> | ||
| myvalueabc | myvalueabc | ||
| - | STORED | + | |
| + | STORED | ||
| </code> | </code> | ||
| **output notes:** | **output notes:** | ||
| Line 149: | Line 141: | ||
| <code> | <code> | ||
| append mykey 0 120 10 | append mykey 0 120 10 | ||
| - | </code> | ||
| - | **output:** | ||
| - | <code> | ||
| defghijklm | defghijklm | ||
| - | STORED | + | |
| + | STORED | ||
| </code> | </code> | ||
| **output notes:** | **output notes:** | ||
| Line 171: | Line 161: | ||
| <code> | <code> | ||
| prepend mykey 0 120 10 | prepend mykey 0 120 10 | ||
| - | </code> | ||
| - | **output:** | ||
| - | <code> | ||
| abcdeabcde | abcdeabcde | ||
| - | STORED | + | |
| + | STORED | ||
| </code> | </code> | ||
| **output notes:** | **output notes:** | ||
| Line 184: | Line 172: | ||
| ===== cas ===== | ===== cas ===== | ||
| - | Check-and-Set an item; store data only if no one else has updated since the last fetch, determined with the **cas token** from the **gets** command. | + | Check-and-Set an item; store data only if no one else has updated since the last fetch, determined with the cas token from the **gets** command. |
| **syntax:** | **syntax:** | ||
| Line 193: | Line 181: | ||
| <code> | <code> | ||
| cas mykey 0 120 10 2 | cas mykey 0 120 10 2 | ||
| - | </code> | ||
| - | **output:** | ||
| - | <code> | ||
| abcdeabcde | abcdeabcde | ||
| - | STORED | + | |
| + | STORED | ||
| </code> | </code> | ||
| **output notes:** | **output notes:** | ||
| Line 215: | Line 201: | ||
| <code> | <code> | ||
| incr mykey 4 | incr mykey 4 | ||
| - | </code> | + | |
| - | **output:** | + | |
| - | <code> | + | |
| 5 | 5 | ||
| </code> | </code> | ||
| Line 234: | Line 218: | ||
| <code> | <code> | ||
| decr mykey 3 | decr mykey 3 | ||
| - | </code> | + | |
| - | **output:** | + | |
| - | <code> | + | |
| 2 | 2 | ||
| </code> | </code> | ||
| Line 253: | Line 235: | ||
| <code> | <code> | ||
| delete mykey | delete mykey | ||
| - | </code> | + | |
| - | **output:** | + | |
| - | <code> | + | |
| DELETED | DELETED | ||
| </code> | </code> | ||
| Line 269: | Line 249: | ||
| <code> | <code> | ||
| touch mykey 1200 | touch mykey 1200 | ||
| - | </code> | + | |
| - | **output:** | + | |
| - | <code> | + | |
| TOUCHED | TOUCHED | ||
| </code> | </code> | ||
| Line 287: | Line 265: | ||
| <code> | <code> | ||
| stats | stats | ||
| - | </code> | + | |
| - | **output:** | + | |
| - | <code> | + | |
| STAT pid 16825 | STAT pid 16825 | ||
| STAT version 1.0.0 | STAT version 1.0.0 | ||
| Line 319: | Line 295: | ||
| <code> | <code> | ||
| stats reset | stats reset | ||
| - | </code> | + | |
| - | **output:** | + | |
| - | <code> | + | |
| RESET | RESET | ||
| </code> | </code> | ||
| Line 335: | Line 309: | ||
| <code> | <code> | ||
| flush_all | flush_all | ||
| - | </code> | + | |
| - | **output:** | + | |
| - | <code> | + | |
| OK | OK | ||
| </code> | </code> | ||
| Line 351: | Line 323: | ||
| <code> | <code> | ||
| version | version | ||
| - | </code> | + | |
| - | **output:** | + | |
| - | <code> | + | |
| VERSION 1.0.0 | VERSION 1.0.0 | ||
| </code> | </code> | ||
| Line 367: | Line 337: | ||
| <code> | <code> | ||
| quit | quit | ||
| - | </code> | + | |
| - | **output:** | + | |
| - | <code> | + | |
| Connection closed by foreign host. | Connection closed by foreign host. | ||
| </code> | </code> | ||
| Line 383: | Line 351: | ||
| <code> | <code> | ||
| verbosity 1 | verbosity 1 | ||
| - | </code> | + | |
| - | **output:** | + | |
| - | <code> | + | |
| OK | OK | ||
| </code> | </code> | ||