Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision Last revision Both sides next revision | ||
litespeed_wiki:admin:command-reference [2019/08/29 14:21] qtwrk |
litespeed_wiki:admin:command-reference [2019/09/24 15:31] Jackson Zhang [Commands Reference] |
||
---|---|---|---|
Line 1: | Line 1: | ||
======Commands Reference====== | ======Commands Reference====== | ||
- | This reference lists all the commands for LiteSpeed WebServer (LSWS) and LiteSpeed ADC (LSLB). | + | This reference lists all of the commands for LiteSpeed WebServer (LSWS) and LiteSpeed Web ADC (ADC). |
- | * For LSWS, assume it's installed under ''/usr/local/lsws/'' | + | |
- | * For LSLB, assume it's installed under ''/usr/local/lslb/'', the commands are same as LSWS, you can just replace ''lsws'' with ''lslbd''. | + | **Note**: LiteSpeed Web ADC was previously known as LiteSpeed Load Balancer, hence the ''lslb'' references throughout. |
+ | |||
+ | By default, the commands covered here can be found in ''/usr/local/lsws/bin/'' for LSWS and in ''/usr/local/lslb/bin/'' for ADC. | ||
=====Control Commands===== | =====Control Commands===== | ||
- | * For LSLB, the command is ''lslbctrl'' | + | |
- | **/usr/local/lsws/bin/lswsctrl help** -- will list the below options | + | |
<code> | <code> | ||
Usage: ./lswsctrl {start|stop|restart|reload|condrestrt|try-restart|status|help} | Usage: ./lswsctrl {start|stop|restart|reload|condrestrt|try-restart|status|help} | ||
Line 21: | Line 22: | ||
</code> | </code> | ||
- | ====SysVinit:==== | + | **Note**: For ADC, the command is ''./lslbctrl''. |
+ | |||
+ | ====SysVinit==== | ||
<code> | <code> | ||
Line 41: | Line 44: | ||
<code> chkconfig lsws {on|off} </code> | <code> chkconfig lsws {on|off} </code> | ||
- | ====systemd:==== | + | ====systemd==== |
<code> | <code> | ||
Line 54: | Line 57: | ||
status - show service status | status - show service status | ||
</code> | </code> | ||
- | |||
- | **Note**: ''lsws'' may vary depends on environment, it could also be ''litespeed'' or ''lshttpd'', for LiteSpeed ADC, it should be ''lslb'' | ||
To enable auto-start on system boot: | To enable auto-start on system boot: | ||
<code>systemctl enable lsws</code> | <code>systemctl enable lsws</code> | ||
+ | |||
+ | **Note**: The ''lsws'' parameter used with ''systemctl'' may vary depending on the environment. It may also be ''litespeed'' or ''lshttpd''. For Web ADC, use ''lslb''. | ||
=====License Commands===== | =====License Commands===== | ||
Line 82: | Line 85: | ||
=====Misc Commands===== | =====Misc Commands===== | ||
- | * If you forgot your admin web console login, you can reset your password from command line | + | * If you forget your admin web console login, you can reset your password from the command line |
/usr/local/lsws/admin/misc/admpass.sh | /usr/local/lsws/admin/misc/admpass.sh |